Incremental encoder is commonly used, and absolute encoder is used if there are strict requirements on position and zero position. Servo system should be analyzed in detail, depending on the application situation. Commonly used incremental encoder for speed measurement, which can be used for infinite accumulation measurement; Absolute encoder is used for position measurement, and the position is unique (single or multiple turns). Finally, it depends on the application situation and the purpose and requirements to be realized.
"The encoder is generally divided into incremental encoder and absolute value encoder. The output mode of incremental encoder includes RS422, push-pull HTL, push-pull and NPN collector open circuit output; the output code system of absolute value encoder is generally binary code, also has gray code, and the output logic includes positive logic, negative logic and SSI.
Classification by encoder mechanical installation form(1) Shaft type: shaft type can be divided into clamping flange type, synchronous flange type and servo installation type.(2) Shaft sleeve type: shaft sleeve type can be divided into half empty type, full empty type and large diameter type.
Rotate incremental encoder to output pulse when rotating, and know its position by counting equipment. When encoder is stationary or power failure, it depends on the internal memory of counting equipment to remember the position. In this way, after power failure, the encoder can't move at all, and when the incoming call works, the encoder can't lose the pulse due to interference in the process of outputting the pulse. Otherwise, the memory zero of the counting equipment will shift, and the...
Encoders are generally divided into incremental encoder and absolute encoder, which have the biggest difference: in the case of incremental encoder, the position is determined by the number of pulses calculated from the zero mark, while the position of absolute encoder is determined by the reading of output code. In a circle, the reading of the output code of each position is unique; Therefore, when the power supply is turned off, the absolute encoder is not separated from the actual position....
The rotary incremental encoder outputs pulses when rotating, and the position is known by the counting device. When the encoder does not move or the power is off, the internal memory of the counting device is used to remember the position. In this way, when the power is cut off, the encoder cannot move in any way. When the power is called to work, the encoder can not lose the pulse due to interference during the output pulse process. Otherwise, the zero point memorized by the counting device...
At present, the encoder used in elevator is mainly incremental encoder, which is used together with frequency converter or other speed control system to provide speed and position information for speed control system or control system. Generally, frequency divider is added for pulse equivalent conversion. Encoder installation is mainly coaxial connection with traction motor to measure speed and feedback of motor. Now the door motor of frequency conversion door system is also equipped with...
An encoder is a device that compiles signals (such as bit streams) or data and converts them into signal forms that can be used for communication, transmission and storage.Encoder converts angular displacement or linear displacement into electrical signals, the former is called code wheel and the latter is called code scale.
The main performance requirements of encoder are: high precision, high sensitivity, reliable work, good stability, strong anti-interference ability, good dynamic characteristics, simple structure and low cost. The main items to be checked include: appearance; starting moment of main shaft; allowable speed; allowable axle load (axial and radial); inertia moment; vibration resistance; shock resistance; high temperature resistance; anti-interference ability; power voltage adaptability; current...
Working principle and function of encoder: it is a rotary sensor that converts rotary displacement into a series of digital pulse signals. These pulses can be used to control angular displacement. If the encoder is combined with gear bar or screw, it can also be used to measure linear displacement.
Function of rotary encoder in elevator 1).It is used to monitor the elevator speed and realize the closed-loop control 2).Some elevators also use rotary encoder to measure the speed and cooperate with the brake device to realize the upward overspeed protection.
The absolute encoder outputs multi-bit digital code (gray code or pure binary code), and the parallel output means that there are many high and low level outputs on the interface to represent digital 1 or 0. For the absolute encoder with low number of bits, the digital code is generally output directly in this form, which can directly enter the I/O interface of PLC or upper computer, with immediate output and simple connection.
In practice, the faults caused by rotary encoder are not a few, and it is quite troublesome to check. Sometimes, although it has been checked, it is still not reassuring. Therefore, I would like to introduce a simple method to confirm the rotary coding fault. From the schematic diagram of the drive and regulation system, it can be clearly seen that it is because of the rotary coding that the microcomputer inverter motor is between. If there is a problem with the rotary encoder, the abnormal...
An encoder is a device that compiles signals (such as bit streams) or data and converts them into signal forms that can be used for communication, transmission and storage.Encoder converts angular displacement or linear displacement into electrical signals, the former is called code wheel and the latter is called code scale.
Absolute encoder is relatively inaccurate in measuring small angle, but there is no cumulative error in large angle measurement.
The absolute encoder outputs multi-bit digital code (gray code or pure binary code), and the parallel output means that there are many high and low level outputs on the interface to represent digital 1 or 0. For the absolute encoder with low number of bits, the digital code is generally output directly in this form, which can directly enter the I/O interface of PLC or upper computer, with immediate output and simple connection.
It is a speed and displacement sensor which integrates optical electromechanical technology. When the rotating encoder shaft drives the grating disk to rotate, the light emitted by the light-emitting element is cut into intermittent light by the slit of the grating disc, and is received by the receiving element to generate the initial signal.
Rotating photoelectric encoder is a mature technology for measuring angle and length. Nowadays, using absolute encoder with high precision and large range greatly improves the measurement accuracy and reliability, and is economical and practical. At present, it is still the most choice for measuring length.
The incremental rotary encoder has the difference of resolution, which is measured by the number of pulses per turn, ranging from 6 to 5400 or higher, and the more pulses, the higher the resolution; This is one of the important basis for selection.
Rotating photoelectric encoder is a mature technology for measuring angle and length. Nowadays, using absolute encoder with high precision and large range greatly improves the measurement accuracy and reliability, and is economical and practical. At present, it is still the most choice for measuring length.
High quality Optical encoders linear Incremental encoder is commonly used, and absolute encoder is used if there are strict requirements on position and zero position. Servo system should be analyzed in detail, depending on the application situation. Commonly used incremental encoder for speed measurement, which can be used for infinite accumulation measurement; Absolute encoder is used for position measurement, and the position is unique (single or multiple turns). Finally, it depends on the...
Model NO.: N40 neodymium magnet Shape: Block Grade: N40
100% good quality S50- Series incremental linear encoder Product Description 1) Advantages incremental linear encoder 1, Certification: CE & ISO9001 & SGS. 2, Feature: sturdy and durable, optional various output mode, long service life, low price, etc....
HENGXIANG S50 incremental linear encoder 2048ppr long dirver 7272 1) Advantages 1, Certification: CE & ISO9001 & SGS. 2, Feature: sturdy and durable, optional various output mode, long service life, low price, etc. 3, Application:
Product Description S38 solid shaft encoder 1) Advantages 1, Certification: CE& ISO9001 & SGS. 2, Feature: microminiature, logical compact configuration and easy to install. 3, Application: subminiature motor, small instrument, etc., for automation control 2) S38- Series Encoder Specification
Product Description S50 solid shaft encoder 1) Advantages 1, Certification: CE& ISO9001 & SGS. 2, Feature: microminiature, logical compact configuration and easy to install. 3, Application: subminiature motor, small instrument, etc., for automation control 2) S50- Series Encoder Specification
Model NO.: N40 neodymium magnet Shape: Block Grade: N40
100% good quality S50- Series incremental linear encoder Product Description 1) Advantages incremental linear encoder 1, Certification: CE & ISO9001 & SGS. 2, Feature: sturdy and durable, optional various output mode, long service life, low price, etc....
Send Inquiry
Ms. carol Dong
Tel:86-431-85543703
Fax:86-431---88634119
Mobile Phone:+8613894866263
Email:sales@encoders.com.cn
Address:333Feiyue Donglu, Changchun City, Jilin Province. China, Changchun, Jilin
Related Products List
Mobile Site
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
